Internet-Draft Export of On-Path Delay in IPFIX January 2024
Graf, et al. Expires 17 July 2024 [Page]
Workgroup:
Network Working Group
Internet-Draft:
draft-ietf-opsawg-ipfix-on-path-telemetry-06
Published:
Intended Status:
Standards Track
Expires:
Authors:
T. Graf
Swisscom
B. Claise
Huawei
A. Huang Feng
INSA-Lyon

Export of On-Path Delay in IPFIX

Abstract

This document introduces new IP Flow Information Export (IPFIX) information elements to expose the On-Path Telemetry measured delay on the IOAM transit and decapsulation nodes.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 17 July 2024.

Table of Contents

1. Introduction

Network operators want a statistical delay view of their networks. They want to understand where in the network, for which customer traffic, how much and why delay is being accummlated. In order to answer why and where, delay needs to be reported into device and control-plane context. In order to understand which customer traffic is affected, delay needs to be reported into customer data-plane context. That enables network operators to quickly identify when the control-plane updates the current path with a different next-hop and therefore the forwarding path changes to different nodes and interfaces, how the path delay changes for which customer traffic.

With On-Path Telemetry, described in the Network Telemetry Framework [RFC9232] and applied in In-situ OAM [I-D.ietf-ippm-ioam-deployment] and Alternate Marking Deployment Framework [I-D.ietf-ippm-alt-mark-deployment], the path delay between two endpoints is measured by inserting a timestamp in the packet.

On-Path Telemetry can be distinguished between two modes. Passport mode, [RFC9197], where only the last hop in the forwarding path of the On-Path Telemetry domain exposes all the metrics, and postcard mode, [I-D.song-ippm-postcard-based-telemetry], where the metrics are also exposed in the transit nodes. In both modes the forwarding path exposes performance metrics allowing to determine how much delay has been accumulated on which hop.

This document defines four new IPFIX Information Elements (IEs), exposing the On-Path delay on IOAM transit and decapsulation nodes, following the postcard mode principles. Since these IPFIX IEs are performance metrics [RFC8911], they must be registered in the "IANA Performance Metric Registry [IANA-PERF-METRIC].

Following the guidelines for Registered Performance Metric requesters and reviewers [RFC8911], the different characteristics of the performance metrics (Identifier, Name, URI, Status, Requester, Revision, Revision Date, Description, etc) must be clearly specified in the "IANA Performance Metric Registry [IANA-PERF-METRIC] in order for the results of measurements using the Performance Metrics to be comparable even if they are performed by different implementations and in different networks. These characteristics start by selecting a meaningful name, following the "MetricType_Method_SubTypeMethod_... Spec_Units_Output" naming convention (See Section 7.1.2 of [RFC8911]).

+------------------------------------+-------------------------------+
|      Performance Metric            |  IPFIX Information Element    |
+------------------------------------+-------------------------------+
|OWDelay_HybridType1_Passive_I       |PathDelayMeanDeltaMicroseconds |
|P_RFC[RFC-to-be]_Seconds_Mean (TBD1)|(TBD5)                         |
+------------------------------------+-------------------------------+
|OWDelay_HybridType1_Passive_I       |PathDelayMinDeltaMicroseconds  |
|P_RFC[RFC-to-be]_Seconds_Min (TBD2) |(TBD6)                         |
+------------------------------------+-------------------------------+
|OWDelay_HybridType1_Passive_I       |PathDelayMaxDeltaMicroseconds  |
|P_RFC[RFC-to-be]_Seconds_Max (TBD3) |(TBD7)                         |
+------------------------------------+-------------------------------+
|OWDelay_HybridType1_Passive_I       |PathDelaySumDeltaMicroseconds  |
|P_RFC[RFC-to-be]_Seconds_Sum (TBD4) |(TBD8)                         |
+------------------------------------+-------------------------------+

Table 1: Correspondance between IPFIX IE and Performance Metric

The delay is measured by calculating the difference between the timestamp imposed with On-Path Telemetry in the packet at the IOAM encapsulation node and the timestamp exported in the IPFIX flow record from the IOAM transit and decapsulation nodes. The lowest, highest, mean, and/or the sum of measured path delay can be exported, thanks to the different IPFIX IE specifications.

                       On-Path Telemetry Domain
              .........................................
              .                                       .
              .    D1                                 .
              . <------>                              .
              .                                       .
              .          D2                           .
              . <-------------------->                .
              .                                       .
              .                  D3                   .
              . <-----------------------------------> .
              .                                       .
(H1) ------ (R1) ------- (R2) ------- (R3) -------- (R4) ------ (H2)
Host 1  Encapsulation   Transit      Transit   Decapsulation  Host 2
            Node         Node 1       Node 2        Node
              .                                       .
              .                                       .
              .........................................

Figure 1: Delay use case. Packets flow from host 1 to host 2.

On the usecase showed in Figure 1 using On-path Telemetry to export the delay metrics, the node R2 exports the delay D1, the node R3 exports the delay D2 and the decapsulation node R4 exports the total delay D3 using IPFIX.

2. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

This document makes use of the terms defined in [RFC7011] and [I-D.ietf-ippm-ioam-deployment].

The following terms are used as defined in [RFC7011].

The following terms are used as defined in [RFC8911].

The following terms are used as defined in [I-D.ietf-ippm-ioam-deployment].

3. Performance Metrics

This section defines and describes the new performance metrics by applying the template defined in Section 11 of [RFC8911].

3.1. IP One-Way Delay Hybrid Type I Passive Performance Metrics

This section specifies four performance metrics for the Hybrid Type I Passive assessment of IP One-Way Delay, to be registered in the "IANA Performance Metric Registry [IANA-PERF-METRIC].

All column entries besides the ID, Name, Description, and Output Reference Method categories are the same; thus, this section defines four closely related performance metrics. As a result, IANA has assigned corresponding URLs to each of the four registered performance metrics.

3.1.1. Summary

This category includes multiple indexes of the registered performance metrics: the element ID and Metric Name.

3.1.1.1. ID (Identifier)

<insert a numeric Identifier, an integer, TBD>

3.1.1.2. Name

IANA has allocated the numeric Identifiers TBD1-4 for the four Named Metric Entries in this section

3.1.1.3. Name

TBD1: OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Mean

TBD2: OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Min

TBD3: OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Max

TBD4: OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Sum

3.1.1.4. URI

URL: https://www.iana.org/assignments/performance-metrics/OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Mean

URL: https://www.iana.org/assignments/performance-metrics/OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Min

URL: https://www.iana.org/assignments/performance-metrics/OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Max

URL: https://www.iana.org/assignments/performance-metrics/OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Sum

3.1.2. Description

This metric assesses the one-way delay of IP packets constituting a single connection between two hosts. We consider the measurement of one-way delay based on a single Observation Point (OP) [RFC7011] somewhere in the network. The output is the one-way delay for all successfully forwarded packets expressed as the <statistic> of their conditional delay distribution, where <statistic> is one of:

3.1.3. Change Controller

IETF

3.1.4. Version of Registry Format

1.0

3.2. Metric Definition

This category includes columns to prompt the entry of all necessary details related to the metric definition, including the immutable document reference and values of input factors, called "Fixed Parameters".

3.2.1. Reference Definition

Almes, G., Kalidindi, S., Zekauskas, M., and A. Morton, Ed., "A One-Way Delay Metric for IP Performance Metrics (IPPM)", STD 81, RFC 7679, DOI 10.17487/RFC7679, January 2016, <https://www.rfc-editor.org/info/rfc7679>. [RFC7679]

Morton, A. and E. Stephan, "Spatial Composition of Metrics", RFC 6049, DOI 10.17487/RFC6049, January 2011, <https://www.rfc-editor.org/info/rfc6049>. [RFC6049]

Section 3.4 of [RFC7679] provides the reference definition of the singleton (single value) one-way delay metric. Section 4.4 of [RFC7679] provides the reference definition expanded to cover a multi-value sample. Note that terms such as "singleton" and "sample" are defined in section 2 of [RFC2330].

With the OP [RFC7011] typically located between the hosts participating in the IP connection, the one-way delay metric requires one individual measurement between the OP and sourcing host, such that the Spatial Composition [RFC6049] of the measurements yields a one-way delay singleton.

3.2.2. Fixed Parameters

Traffic Filters:

 IPv4 header values:
   DSCP: Set to 0

 IPv6 header values:
   DSCP: Set to 0
   Hop Count: Set to 255
   Flow Label: Set to 0
   Extension Headers: None

3.3. Method of Measurement

This category includes columns for references to relevant sections of the RFC(s) and any supplemental information needed to ensure an unambiguous method for implementations.

3.3.1. Reference Methods

The foundational methodology for this metric is defined in section 4 of [RFC7323] using the Timestamps option with modifications that allow application at a mid-path OP [RFC7011].

3.3.2. Packet Stream Generation

N/A

3.3.3. Traffic Filtering (Observation) Details

The Fixed Parameters above give a portion of the Traffic Filter. Other aspects will be supplied as Runtime Parameters (below).

3.3.4. Sampling Distribution

This metric requires a partial sample of all packets that qualify according to the Traffic Filter criteria.

3.3.5. Runtime Parameters and Data Format

Runtime Parameters are input factors that must be determined, configured into the measurement system, and reported with the results for the context to be complete.

The hybrid type I metering parameters must must be reported to provide the complete measurement context. As an example, if the IPFIX metering process is used, then the IPFIX metering process parameters (IPFIX template record used, potential traffic filters, and potential sampling method and parameters) that generates the flow records must be reported to provide the complete measurement context.

Src:
The IP address of the host in the host A Role (format ipv4‑address-no-zone value for IPv4 or ipv6-address-no-zone value for IPv6; see section 4 of [RFC6991].
Dst:
The IP address of the host in the host B Role (format ipv4‑address-no-zone value for IPv4 or ipv6-address-no-zone value for IPv6; see section 4 of [RFC6991].
TTL or Hop Limit:
Set at desired value.
DSCP:
Set at desired value.
IPv6 Flow Label:
Set at desired value.
Timestamp:
The timestamp when the packet is being received at IOAM encapsulation node. Format depends on On-Path Telemetry implementation. For IOAM, Section 4.4.1 of [RFC9197] describes what kind of timestamps are supported. Section 4.4.2.3 and 4.4.2.4 describe where the timestamp is being inserted. For the Enhanced Alternate Marking Method, Section 2 of [I-D.zhou-ippm-enhanced-alternate-marking] describes timestamp encoding and granularity.

3.3.6. Roles

host A:
Launches the IP packet to open the connection. The Role of "host A" is synonymous with the IP address used at host A.
host B:
Receives the IP packet to open the connection. The Role of "host B" is synonymous with the IP address used at host B.
Encapsulation Node:
Receives the IP packet to open the connection and encapsulates the timestamp into the packet. The Role of "Encapsulation Node" is synonymous with the timestamp inserted in the packet.
Transit Node:
Receives the IP packet to open the connection and measures the delay between the timestamp in the packet and the timestamp when the packet was received.
Decapsulation Node:
Receives the IP packet to open the connection and measures the delay between the timestamp in the packet and the timestamp when the packet was received and removes the IOAM header from the packet.

3.4. Output

This category specifies all details of the output of measurements using the metric.

3.4.1. Type

OWDelay Types are discussed in the subsections below.

3.4.2. Reference Definition

For all output types:

OWDelay_HybridType1_Passive_IP:
The one-trip delay of one IP packet is a Singleton

For each <statistic> Singleton one of the following subsections applies.

3.4.2.1. Mean

The mean SHALL be calculated using the conditional distribution of all packets with a finite value of one-way delay (undefined delays are excluded) -- a single value, as follows:

See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and see section 5 of [RFC6703] for background on this analysis choice.

See section 4.2.2 of [RFC6049] for details on calculating this statistic; see also section 4.2.3 of [RFC6049].

Mean:
The time value of the result is expressed in units of seconds, as a positive value of type decimal64 with fraction digits = 9 (see section 9.3 of [RFC6020]) with a resolution of 0.000000001 seconds (1.0 ns), and with lossless conversion to/from the 64-bit NTP timestamp as per section 6 of [RFC5905].
3.4.2.2. Min

The minimum SHALL be calculated using the conditional distribution of all packets with a finite value of one-way delay (undefined delays are excluded) -- a single value, as follows:

See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and see section 5 of [RFC6703] for background on this analysis choice.

See section 4.3.2 of [RFC6049] for details on calculating this statistic; see also section 4.3.3 of [RFC6049].

Min:
The time value of the result is expressed in units of seconds, as a positive value of type decimal64 with fraction digits = 9 (see section 9.3 of [RFC6020]) with a resolution of 0.000000001 seconds (1.0 ns), and with lossless conversion to/from the 64-bit NTP timestamp as per section 6 of [RFC5905].
3.4.2.3. Max

The maximum SHALL be calculated using the conditional distribution of all packets with a finite value of one-way delay (undefined delays are excluded) -- a single value, as follows:

See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and see section 5 of [RFC6703] for background on this analysis choice.

See section 4.3.2 of [RFC6049] for a closely related method for calculating this statistic; see also section 4.3.3 of [RFC6049]. The formula is as follows:

 Max = (FiniteDelay[j])
 such that for some index, j, where 1 <= j <= N
 FiniteDelay[j] >= FiniteDelay[n] for all n

where all packets n = 1 through N have finite singleton delays.

Max:
The time value of the result is expressed in units of seconds, as a positive value of type decimal64 with fraction digits = 9 (see section 9.3 of [RFC6020]) with a resolution of 0.000000001 seconds (1.0 ns), and with lossless conversion to/from the 64-bit NTP timestamp as per section 6 of [RFC5905].
3.4.2.4. Sum

The sum SHALL be calculated using the conditional distribution of all packets with a finite value of one-way delay (undefined delays are excluded) -- a single value, as follows:

See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and see section 5 of [RFC6703] for background on this analysis choice.

See section 4.3.5 of [RFC6049] for details on calculating this statistic. However in this case FiniteDelay or MaxDelay MAY be used.

Sum:
The time value of the result is expressed in units of seconds, as a positive value of type decimal64 with fraction digits = 9 (see section 9.3 of [RFC6020]) with a resolution of 0.000000001 seconds (1.0 ns), and with lossless conversion to/from the 64-bit NTP timestamp as per section 6 of [RFC5905].
3.4.2.5. Metric Units

The <statistic> of one-way delay is expressed in seconds, where <statistic> is one of:

The one-way delay of the IP connection singleton is expressed in seconds.

3.4.2.6. Calibration

Passive Measurements at an OP could be calibrated against an Active Measurement at host A where the Active Measurement represents the ground truth.

3.4.3. Administrative Items

3.4.3.1. Status

Current

3.4.3.2. Requester

This RFC

3.4.3.3. Revision

1.0

3.4.3.4. Revision Date

RFC Date

3.4.4. Comments and Remarks

none

4. IPFIX Information Elements

This section defines and describes the new IPFIX IEs.

PathDelayMeanDeltaMicroseconds
32-bit unsigned integer that identifies the mean path delay in microseconds, between the IOAM encapsulation node and the local node with the IOAM domain (either an IOAM transit node or an IOAM decapsulation node).
PathDelayMinDeltaMicroseconds
32-bit unsigned integer that identifies the lowest path delay in microseconds, between the IOAM encapsulation node and the local node with the IOAM domain (either an IOAM transit node or an IOAM decapsulation node).
PathDelayMaxDeltaMicroseconds
32-bit unsigned integer that identifies the highest path delay in microseconds, between the IOAM encapsulation node and the local node with the IOAM domain (either an IOAM transit node or an IOAM decapsulation node).
PathDelaySumDeltaMicroseconds
64-bit unsigned integer that identifies the sum of the path delay in microseconds, between the IOAM encapsulation node and the local node with the IOAM domain (either an IOAM transit node or an IOAM decapsulation node).

5. Use Cases

The measured On-Path delay can be aggregated with Flow Aggregation as defined in [RFC7015] to the following device and control-plane dimensions to determine:

Taking figure 1 from section 1 as topology example. Below example table shows the aggregated delay per each node, ingressInterface, egressInterface, destinationIPv6Address and srhActiveSegmentIPv6.

     +-----------+-----------+------+-------------+-------------+------------+
     | ingress   | egress    | Node | destination | srhActive   | Path Delay |
     | Interface | Interface |      | IPv6Address | SegmentIPv6 |            |
     +-----------+-----------+------+-------------+-------------+------------+
     |    271    |    276    |  R1  | 2001:db8::2 | 2001:db8::4 |    0 us    |
     +-----------+-----------+------+-------------+-------------+------------+
     |    301    |    312    |  R2  | 2001:db8::3 | 2001:db8::4 |   22 us    |
     +-----------+-----------+------+-------------+-------------+------------+
     |    22     |     27    |  R3  | 2001:db8::4 | 2001:db8::4 |   42 us    |
     +-----------+-----------+------+-------------+-------------+------------+
     |    852    |    854    |  R4  | 2001:db8::4 | 2001:db8::4 |  122 us    |
     +-----------+-----------+------+-------------+-------------+------------+

           Table 2: Example table of measured delay. Ascending by delay.

6. IANA Considerations

6.1. Performance Metrics

This document requests IANA to create new performance metrics under the "Performance Metrics" registry [RFC8911] with the values defined in section 2.

6.2. IPFIX Entities

This document requests IANA to create new IPFIX IEs (see table 3) under the "IPFIX Information Elements" registry [RFC7012] available at "IANA Performance Metric Registry [IANA-PERF-METRIC] and assign the following initial code points.

     +-------+--------------------------------+
     |Element|              Name              |
     |   ID  |                                |
     +-------+--------------------------------+
     | TBD5  | PathDelayMeanDeltaMicroseconds |
     |       |                                |
     +-------+--------------------------------+
     | TBD6  | PathDelayMinDeltaMicroseconds  |
     |       |                                |
     +-------+--------------------------------+
     | TBD7  | PathDelayMaxDeltaMicroseconds  |
     |       |                                |
     +-------+--------------------------------+
     | TBD8  | PathDelaySumDeltaMicroseconds  |
     |       |                                |
     +-------+--------------------------------+
  Table 3: Creates IPFIX IEs in the "IPFIX Information Elements" registry

Note to the RFC-Editor:

  • Please replace TBD5 - TBD8 with the values allocated by IANA

  • Please replace the [RFC-to-be] with the RFC number assigned to this document

6.2.1. PathDelayMeanDeltaMicroseconds

Name:
PathDelayMeanDeltaMicroseconds
ElementID:
TBD5
Description:
This Information Element identifies the mean path delay between the IOAM encapsulation node and the local node with the IOAM domain (either an IOAM transit node or an IOAM decapsulation node) in microseconds, according to OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Mean in the IANA Performance Metric Registry
Abstract Data Type:
unsigned32
Data Type Semantics:
deltaCounter
Reference:
[RFC-to-be], OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Mean in the IANA Performance Metric Registry.

6.2.2. PathDelayMinDeltaMicroseconds

Name:
PathDelayMinDeltaMicroseconds
ElementID:
TBD6
Description:
This Information Element identifies the lowest path delay between the IOAM encapsulation node and the local node with the IOAM domain (either an IOAM transit node or an IOAM decapsulation node) in microseconds, according to the OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Min in the IANA Performance Metric Registry.
Abstract Data Type:
unsigned32
Data Type Semantics:
deltaCounter
Reference:
[RFC-to-be], OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Min in the IANA Performance Metric Registry.

6.2.3. PathDelayMaxDeltaMicroseconds

Name:
PathDelayMaxDeltaMicroseconds
ElementID:
TBD7
Description:
This Information Element identifies the highest path delay between the IOAM encapsulation node and the local node with the IOAM domain (either an IOAM transit node or an IOAM decapsulation node) in microseconds, according to OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Max in the IANA Performance Metric Registry.
Abstract Data Type:
unsigned32
Data Type Semantics:
deltaCounter
Reference:
[RFC-to-be], OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Max in the IANA Performance Metric Registry.

6.2.4. PathDelaySumDeltaMicroseconds

Name:
PathDelaySumDeltaMicroseconds
ElementID:
TBD8
Description:
This Information Element identifies the sum of the path delay between the IOAM encapsulation node and the local node with the IOAM domain (either an IOAM transit node or an IOAM decapsulation node) in microseconds, according to OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Sum in the IANA Performance Metric Registry.
Abstract Data Type:
unsigned64
Data Type Semantics:
deltaCounter
Reference:
[RFC-to-be], OWDelay_HybridType1_Passive_IP_RFC[RFC-to-be]_Seconds_Sum in the IANA Performance Metric Registry.

7. Operational Considerations

7.1. Time Accuracy

The same recommendation as defined in section 4.5 of [RFC5153] for IPFIX applies in terms of clock precision to this document as well.

7.2. Mean Delay

The mean (average) path delay can be calculated by dividing the PathDelaySumDeltaMicroseconds(TBD5) by the packetDeltaCount(2) at the IPFIX data collection in order to offload the IPFIX Exporter from calculating the mean for every Flow at export time.

7.3. Reduced-size encoding

Unsigned64 has been chosen as type for PathDelaySumDeltaMicroseconds to support cases with large delay numbers and where many packets are being accounted. As an example, a specific flow record with path delay of 100 microseconds can not observe more than 42949 packets without overflowing the unsigned32 counter. The procedure described in Section 6.2 of [RFC7011] could be applied to reduce network bandwidth between the IPFIX Exporter and Collector if unsigned32 would be large enough without wrapping around.

7.4. IOAM Application

This document is applicable in IOAM to the Edge-to-Edge and Direct Exporting Option-Type.

In case of Edge-to-Edge Option-Type, as described in Section 4.6 of [RFC9197], by setting bits 2 and 3, timestamps can be encoded as defined in Section 4.4.2.3 and 4.4.2.4 of [RFC9197].

In case of Direct Exporting Option-Type, as described in Section 2 of [I-D.ahuang-ippm-dex-timestamp-ext], by setting Extension-Flags 2 and 3, timestamps can be encoded as defined in Section 4.4.2.3 and 4.4.2.4 of [RFC9197].

For the Enhanced Alternate Marking Method, Section 2 of [I-D.zhou-ippm-enhanced-alternate-marking] defines that within the metaInfo a nano second timestamp can be encoded in the encapsulation node and be read at the intermediate and decapsulation node to calculate the on-path delay. [RFC9343] defines how this can be appied to the IPv6 data-plane and [I-D.fz-spring-srv6-alt-mark] defines how this can be appied to the Segment Routing Header in SRv6.

8. Security Considerations

There are no significant extra security considerations regarding the allocation of these new IPFIX IEs compared to [RFC7012].

9. Implementation Status

Note to the RFC-Editor: Please remove this section before publishing.

9.1. FD.io VPP

INSA Lyon implemented the following IEs as part of a prototype in the FD.io VPP (Vector Packet Processing) platform:

  • PathDelayMeanDeltaMicroseconds

  • PathDelayMaxDeltaMicroseconds

  • PathDelayMinDeltaMicroseconds

  • PathDelaySumDeltaMicroseconds

The open source code can be obtained here: [INSA-Lyon-VPP] and was validated at the IETF 116 hackathon.

9.2. Huawei VRP

Huawei implemented the following IEs as part of a a production implementation in the VRP platform:

  • PathDelayMeanDeltaMicroseconds

  • PathDelayMaxDeltaMicroseconds

  • PathDelayMinDeltaMicroseconds

  • PathDelaySumDeltaMicroseconds

The implementation was validated at the IETF 116 hackathon.

9.3. Fluvia

NTT Com implemented the following IEs in the Fluvia Exporter:

  • PathDelayMeanDeltaMicroseconds

  • PathDelayMaxDeltaMicroseconds

  • PathDelayMinDeltaMicroseconds

  • PathDelaySumDeltaMicroseconds

The open source code can be obtained here: [NTT-Fluvia] and was validated at the IETF 118 hackathon.

9.4. Pmacct Data Collection

Paolo Lucente implemented the IE PathDelayMeanDeltaMicroseconds by dividing IE PathDelaySumDeltaMicroseconds by IE packetDeltaCount in the open source Network Telemetry data collection project pmacct.

The source code can be obtained here: [Paolo-Lucente-Pmacct] and was validated at the IETF 116 hackathon.

10. Acknowledgements

The authors would like to thank Al Morton, Greg Mirsky and Giuseppe Fioccola for their review and valuable comments.

11. References

11.1. Normative References

[RFC7012]
Claise, B., Ed. and B. Trammell, Ed., "Information Model for IP Flow Information Export (IPFIX)", RFC 7012, DOI 10.17487/RFC7012, , <https://www.rfc-editor.org/info/rfc7012>.
[RFC8911]
Bagnulo, M., Claise, B., Eardley, P., Morton, A., and A. Akhter, "Registry for Performance Metrics", RFC 8911, DOI 10.17487/RFC8911, , <https://www.rfc-editor.org/info/rfc8911>.

11.2. Informative References

[I-D.ahuang-ippm-dex-timestamp-ext]
Feng, A. H., Francois, P., Claise, B., and T. Graf, "Timestamp extension for In Situ Operations, Administration, and Maintenance (IOAM) Direct Export", Work in Progress, Internet-Draft, draft-ahuang-ippm-dex-timestamp-ext-00, , <https://datatracker.ietf.org/doc/html/draft-ahuang-ippm-dex-timestamp-ext-00>.
[I-D.fz-spring-srv6-alt-mark]
Fioccola, G., Zhou, T., Cociglio, M., Mishra, G. S., wang, X., and G. Zhang, "Application of the Alternate Marking Method to the Segment Routing Header", Work in Progress, Internet-Draft, draft-fz-spring-srv6-alt-mark-07, , <https://datatracker.ietf.org/doc/html/draft-fz-spring-srv6-alt-mark-07>.
[I-D.ietf-ippm-alt-mark-deployment]
Fioccola, G., Zhou, T., Graf, T., Nilo, M., and L. Zhang, "Alternate Marking Deployment Framework", Work in Progress, Internet-Draft, draft-ietf-ippm-alt-mark-deployment-00, , <https://datatracker.ietf.org/doc/html/draft-ietf-ippm-alt-mark-deployment-00>.
[I-D.ietf-ippm-ioam-deployment]
Brockners, F., Bhandari, S., Bernier, D., and T. Mizrahi, "In-situ OAM Deployment", Work in Progress, Internet-Draft, draft-ietf-ippm-ioam-deployment-05, , <https://datatracker.ietf.org/doc/html/draft-ietf-ippm-ioam-deployment-05>.
[I-D.song-ippm-postcard-based-telemetry]
Song, H., Mirsky, G., Zhou, T., Li, Z., Graf, T., Mishra, G. S., Shin, J., and K. Lee, "On-Path Telemetry using Packet Marking to Trigger Dedicated OAM Packets", Work in Progress, Internet-Draft, draft-song-ippm-postcard-based-telemetry-16, , <https://datatracker.ietf.org/doc/html/draft-song-ippm-postcard-based-telemetry-16>.
[I-D.zhou-ippm-enhanced-alternate-marking]
Zhou, T., Fioccola, G., Liu, Y., Cociglio, M., Pang, R., Xiong, L., Lee, S., and W. Li, "Enhanced Alternate Marking Method", Work in Progress, Internet-Draft, draft-zhou-ippm-enhanced-alternate-marking-14, , <https://datatracker.ietf.org/doc/html/draft-zhou-ippm-enhanced-alternate-marking-14>.
[IANA-PERF-METRIC]
"IANA Performance Metric Registry", <https://www.iana.org/assignments/performance-metrics/performance-metrics.xhtml>.
[INSA-Lyon-VPP]
"INSA Lyon, FD.io VPP implementation", <https://github.com/network-analytics/vpp-srh-onpath-telemetry>.
[NTT-Fluvia]
"NTT Com, Fluvia Exporter", <https://github.com/nttcom/fluvia/>.
[Paolo-Lucente-Pmacct]
"Paolo Lucente, Pmacct open source Network Telemetry Data Collection", <https://github.com/pmacct/pmacct>.
[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC2330]
Paxson, V., Almes, G., Mahdavi, J., and M. Mathis, "Framework for IP Performance Metrics", RFC 2330, DOI 10.17487/RFC2330, , <https://www.rfc-editor.org/info/rfc2330>.
[RFC3393]
Demichelis, C. and P. Chimento, "IP Packet Delay Variation Metric for IP Performance Metrics (IPPM)", RFC 3393, DOI 10.17487/RFC3393, , <https://www.rfc-editor.org/info/rfc3393>.
[RFC5153]
Boschi, E., Mark, L., Quittek, J., Stiemerling, M., and P. Aitken, "IP Flow Information Export (IPFIX) Implementation Guidelines", RFC 5153, DOI 10.17487/RFC5153, , <https://www.rfc-editor.org/info/rfc5153>.
[RFC5905]
Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch, "Network Time Protocol Version 4: Protocol and Algorithms Specification", RFC 5905, DOI 10.17487/RFC5905, , <https://www.rfc-editor.org/info/rfc5905>.
[RFC6020]
Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, , <https://www.rfc-editor.org/info/rfc6020>.
[RFC6049]
Morton, A. and E. Stephan, "Spatial Composition of Metrics", RFC 6049, DOI 10.17487/RFC6049, , <https://www.rfc-editor.org/info/rfc6049>.
[RFC6703]
Morton, A., Ramachandran, G., and G. Maguluri, "Reporting IP Network Performance Metrics: Different Points of View", RFC 6703, DOI 10.17487/RFC6703, , <https://www.rfc-editor.org/info/rfc6703>.
[RFC6991]
Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, , <https://www.rfc-editor.org/info/rfc6991>.
[RFC7011]
Claise, B., Ed., Trammell, B., Ed., and P. Aitken, "Specification of the IP Flow Information Export (IPFIX) Protocol for the Exchange of Flow Information", STD 77, RFC 7011, DOI 10.17487/RFC7011, , <https://www.rfc-editor.org/info/rfc7011>.
[RFC7015]
Trammell, B., Wagner, A., and B. Claise, "Flow Aggregation for the IP Flow Information Export (IPFIX) Protocol", RFC 7015, DOI 10.17487/RFC7015, , <https://www.rfc-editor.org/info/rfc7015>.
[RFC7323]
Borman, D., Braden, B., Jacobson, V., and R. Scheffenegger, Ed., "TCP Extensions for High Performance", RFC 7323, DOI 10.17487/RFC7323, , <https://www.rfc-editor.org/info/rfc7323>.
[RFC7679]
Almes, G., Kalidindi, S., Zekauskas, M., and A. Morton, Ed., "A One-Way Delay Metric for IP Performance Metrics (IPPM)", STD 81, RFC 7679, DOI 10.17487/RFC7679, , <https://www.rfc-editor.org/info/rfc7679>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
[RFC9197]
Brockners, F., Ed., Bhandari, S., Ed., and T. Mizrahi, Ed., "Data Fields for In Situ Operations, Administration, and Maintenance (IOAM)", RFC 9197, DOI 10.17487/RFC9197, , <https://www.rfc-editor.org/info/rfc9197>.
[RFC9232]
Song, H., Qin, F., Martinez-Julia, P., Ciavaglia, L., and A. Wang, "Network Telemetry Framework", RFC 9232, DOI 10.17487/RFC9232, , <https://www.rfc-editor.org/info/rfc9232>.
[RFC9343]
Fioccola, G., Zhou, T., Cociglio, M., Qin, F., and R. Pang, "IPv6 Application of the Alternate-Marking Method", RFC 9343, DOI 10.17487/RFC9343, , <https://www.rfc-editor.org/info/rfc9343>.
[RFC9487]
Graf, T., Claise, B., and P. Francois, "Export of Segment Routing over IPv6 Information in IP Flow Information Export (IPFIX)", RFC 9487, DOI 10.17487/RFC9487, , <https://www.rfc-editor.org/info/rfc9487>.

Appendix A. IPFIX Encoding Examples

This appendix represents two different encodings for the newly introduced IEs. Taking figure 1 from section 1 as topology example. Below example Table 4 shows the aggregated delay with ingressInterface, egressInterface, destinationIPv6Address and srhActiveSegmentIPv6.

 +------ +------+-----------+-----------+------+---------+---------+---------+---------+
 |ingress|egress|destination|srhActive  |packet|PathDelay|PathDelay|PathDelta|PathDelta|
 |Inter  |Inter |IPv6Address|SegmentIPv6|Delta |MinDelta |MaxDelta |MeanDelta|MeanDelta|
 |face   |face  |           |           |Count |Micro..  |Micro..  |Micro..  |Micro..  |
 +-------+------+-----------+-----------+------+---------+---------+---------+---------+
 |  271  |  276 |2001:db8::4|2001:db8::2|  5   |  22 us  |  74 us  |  36 us  | 180 us  |
 +-------+------+-----------+-----------+------+---------+---------+---------+---------+

  Table 4: Aggregated delay with egressInterface and srhActiveSegmentIPv6

A.1. Aggregated On-Path Dealay Examples

A.1.1. Template Record and Data Set with Mean Delta

With encoding in Figure 1, the mean (average) path delay is calculated on the exporting node.

  • Ingress interface => ingressInterface

  • Egress interface => egressInterface

  • IPv6 destination address => destinationIPv6Address

  • Active SRv6 Segment => srhIPv6ActiveSegment

  • Packet Delta Count => packetDeltaCount

  • Minimum One-Way Delay => PathDelayMinDeltaMicroseconds (TBD6)

  • Maximum One-Way Delay => PathDelayMaxDeltaMicroseconds (TBD7)

  • Mean One-Way Delay => PathDelayMeanDeltaMicroseconds (TBD5)


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |          SET ID = 2           |       Length = 40             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Template ID = 256        |      Field Count = 8          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0|     ingressInterface = 10   |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0|     egressInterface = 14    |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| destinationIPv6Address = 28 |      Field Length = 16        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| srhIPv6ActiveSegment = 495  |      Field Length = 16        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| packetDeltaCount = 5        |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| PathDelayMinDelta.. = TBD6  |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| PathDelayMaxDelta.. = TBD7  |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| PathDelayMeanDelta.. = TBD5 |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     Figure 1: Template Record for PathDelayMeanDeltaMicroseconds

The data set is represented as follows:


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |         SET ID = 256          |           Length = 60         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           ingressInterface =  271                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           egressInterface =  276                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           destinationIPv6Address =                            |
   |                          ...                                  |
   |                          ...                                  |
   |                          2001:db8::2                          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           srhIPv6ActiveSegment = ...                          |
   |                          ...                                  |
   |                          ...                                  |
   |                          2001:db8::4                          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           packetDeltaCount = 5                                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           PathDelayMinDeltaMicroseconds =  22                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           PathDelayMaxDeltaMicroseconds =  74                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           PathDelayMeanDeltaMicroseconds =  36                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

    Figure 2: Data Set Encoding for PathDelayMeanDeltaMicroseconds

A.1.2. Template Record and Data Set with Sum Delta

With encoding in Figure 3, the mean (average) path delay is calculated on the IPFIX data collection.

  • Ingress interface => ingressInterface

  • Egress interface => egressInterface

  • IPv6 destination address => destinationIPv6Address

  • Active SRv6 Segment => srhIPv6ActiveSegment

  • Packet Delta Count => packetDeltaCount

  • Minimum One-Way Delay => PathDelayMinDeltaMicroseconds (TBD6)

  • Maximum One-Way Delay => PathDelayMaxDeltaMicroseconds (TBD7)

  • Sum of One-Way Delay => PathDelaySumDeltaMicroseconds (TBD8)


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |          SET ID = 2           |       Length = 40             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Template ID = 257        |      Field Count = 8          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0|     ingressInterface = 10   |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0|     egressInterface = 14    |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| destinationIPv6Address = 28 |      Field Length = 16        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| srhIPv6ActiveSegment = 495  |      Field Length = 16        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| packetDeltaCount = 5        |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| PathDelayMinDelta.. = TBD6  |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| PathDelayMaxDelta.. = TBD7  |      Field Length = 4         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0| PathDelaySumDelta.. = TBD8  |      Field Length = 8         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     Figure 3: Template Record for PathDelaySumDeltaMicroseconds

The data set is represented as follows:


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |         SET ID = 257          |           Length = 60         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           ingressInterface =  271                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           egressInterface =  276                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           destinationIPv6Address =                            |
   |                          ...                                  |
   |                          ...                                  |
   |                          2001:db8::2                          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           srhIPv6ActiveSegment = ...                          |
   |                          ...                                  |
   |                          ...                                  |
   |                          2001:db8::4                          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           packetDeltaCount = 5                                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           PathDelayMinDeltaMicroseconds =  22                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           PathDelayMaxDeltaMicroseconds =  74                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           PathDelaySumDeltaMicroseconds =  180                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

    Figure 2: Data Set Encoding for PathDelaySumDeltaMicroseconds

Authors' Addresses

Thomas Graf
Swisscom
Binzring 17
CH-8045 Zurich
Switzerland
Benoit Claise
Huawei
Alex Huang Feng
INSA-Lyon
Lyon
France