SPRING B. Varga, Ed. Internet-Draft F. Fejes Intended status: Standards Track Ericsson Expires: 21 June 2025 18 December 2024 Deterministic Networking specific SID draft-varga-spring-preof-sid-01 Abstract Replication, Elimination and Ordering functions of the DetNet Architecture require packet sequence information (i.e., sequence number) to provide service protection by the DetNet service sub- layer. This document extends SRv6 Network Programming [RFC8986] with new SR endpoint and transit behaviors to be performed on packets of DetNet flows to support the specific service protection treatment. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 21 June 2025. Copyright Notice Copyright (c) 2024 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Varga & Fejes Expires 21 June 2025 [Page 1] Internet-Draft PREOF SID December 2024 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1. Terms Used in This Document . . . . . . . . . . . . . . . 3 2.2. Abbreviations . . . . . . . . . . . . . . . . . . . . . . 3 2.3. Requirements Language . . . . . . . . . . . . . . . . . . 3 3. DetNet-specific SID . . . . . . . . . . . . . . . . . . . . . 3 4. SRv6 endpoint behaviors . . . . . . . . . . . . . . . . . . . 4 4.1. End.DPREOF: Endpoint with PREOF . . . . . . . . . . . . . 5 5. SR Policy Headend Behaviors . . . . . . . . . . . . . . . . . 5 5.1. H.Encaps.PREOF: SR Headend with PREOF . . . . . . . . . . 5 5.2. H.Encaps.PREOF.Red: H.Encaps.PREOF with Reduced Encapsulation . . . . . . . . . . . . . . . . . . . . . . 6 5.3. H.Encaps.PREOF.L2: H.Encaps.PREOF Applied to Received L2 Frames . . . . . . . . . . . . . . . . . . . . . . . . . 7 5.4. H.Encaps.PREOF.L2.Red: H.Encaps.PREOF.L2 with Reduced Encapsulation . . . . . . . . . . . . . . . . . . . . . . 7 6. DetNet-specific SID related counters . . . . . . . . . . . . 8 7. Security Considerations . . . . . . . . . . . . . . . . . . . 8 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8 9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 8 10. Normative References . . . . . . . . . . . . . . . . . . . . 8 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 9 1. Introduction The DetNet Working Group has defined Packet Replication (PRF), Packet Elimination (PEF), and Packet Ordering (POF) Functions (represented as PREOF) to provide service protection by the DetNet service sub- layer [RFC8655]. This service protection method relies on copies of the same packet sent over multiple maximally disjoint paths and uses sequencing information to eliminate duplicates before delivered to its destination. DetNet over an SRv6 data plane can provide a solution to transport sequencing information within a SID. This document describes a DetNet-specific SID (SID = Segment Identifier, [RFC8402]) and a set of related packet processing rules inside an SRv6 domain. The DetNet-specific SID provides Flow-ID and Sequence-Number information for the DetNet service sub-layer functions (i.e., PREOF). The usage of DetNet-specific SID provides a native IPv6 data plane for DetNet networks and supports the implementation of PREOF functionalities on IPv6-only DetNet nodes. It is using native SRv6 technology and does not require additional tunneling or implementation of other protocol stack(s) (e.g., MPLS). Varga & Fejes Expires 21 June 2025 [Page 2] Internet-Draft PREOF SID December 2024 2. Terminology 2.1. Terms Used in This Document This document uses the terminology established in the DetNet architecture [RFC8655] and in the SRv6 Network Programming [RFC8986]. The reader is assumed to be familiar with that document and its terminology. 2.2. Abbreviations The following abbreviations are used in this document: ARG Arguments. DetNet Deterministic Networking. FUNCT Function. LOC Locator. PEF Packet Elimination Function. POF Packet Ordering Function. PREOF Packet Replication, Elimination and Ordering Functions. PRF Packet Replication Function. SeqNum Sequence Number. 2.3. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. 3. DetNet-specific SID In SRv6, a SID represents a 128-bit value containing the following three parts [RFC8986]: * Locator (LOC): first part of the SID with most significant bits and represents a specific SRv6 node. Varga & Fejes Expires 21 June 2025 [Page 3] Internet-Draft PREOF SID December 2024 * Function (FUNCT): the portion of the SID that is local to the owner node and designates a specific SRv6 function (network instruction) that is executed locally on a particular node (specified by Locator). * Arguments (ARG): optional field and represents optional argument(s) to the function. For PREOF processing, two arguments are needed: 1. Flow-ID: defines which DetNet flow the packet belongs to (what is used to determine which PREOF instance has to be used on a node). Its size is 20 bits for the DetNet MPLS data plane [RFC8986] and same size is appropriate for DetNet IP data plane as well. 2. Sequence Number: defines the sequencing information, it is created at the DetNet edge node (or by the first PRF node) and used by PEF/POF functionalities. For DetNet MPLS data plane the following sizes are defined: 0/16/28 bits [RFC8964]. The required size for these two arguments are maximum 48 bits. The explicit format of DetNet-specific SID is network addressing design specific. PREOF specific parameters are encoded as follows: * LOC: specifies the DetNet Relay node (same allocation rule applies as for any SRv6-enabled node). * FUNCT: a single value represents all PREOF instances of a DetNet Relay node. * ARG: Contains the Flow-ID and the Sequence Number parameters. Note: if Function=PREOF, Arg=0 is also a meaningful value and does not refer to the lack of arguments. The DetNet-specific SID must be the last segment in an SR Policy and it is associated with the PREOF functionality! The following packet processing rules are defined as a new set of SRv6 SID behaviors regarding the DetNet-specific SID: (i) End.DPREOF, (ii) H.Encaps.PREOF, (iii) H.Encaps.PREOF.Red, (iv) H.Encaps.PREOF.L2, and (v) H.Encaps.PREOF.L2.Red. 4. SRv6 endpoint behaviors This section describes the PREOF specific behaviors that can be associated with a SID. Varga & Fejes Expires 21 June 2025 [Page 4] Internet-Draft PREOF SID December 2024 +-------------+--------------------------------------------------+ | End.DPREOF | Endpoint with decapsulation and PREOF Processing | +-------------+--------------------------------------------------+ Figure 1: PREOF Endpoint Behavior 4.1. End.DPREOF: Endpoint with PREOF When a node "N" receives a packet whose IPv6 DA is "S" and "S" is a local End.DPREOF SID, "N" does the following: S01. When an SRH is processed { S02. If (Segments Left != 0) { S03. Send an ICMP Parameter Problem message to the Source Address with Code 0 (Erroneous header field encountered), and Pointer set to the Segments Left field, interrupt packet processing and discard the packet S04. } S05. Extract the ARG part of the SID S06. Remove the outer IPv6 header with all its extension headers S07. Forward the exposed payload and the ARG part to the PREOF functionality S08. } 5. SR Policy Headend Behaviors This section describes a set of SRv6 Policy Headend [RFC8402] behaviors. +-----------------------+--------------------------------------------------+ | H.Encaps.PREOF | SR Headend with PREOF Encapsulation | +-----------------------+--------------------------------------------------+ | H.Encaps.PREOF.Red | H.Encaps with Reduced PREOF Encapsulation | +-----------------------+--------------------------------------------------+ | H.Encaps.PREOF.L2 | H.Encaps.PREOF Applied to Received L2 Frames | +-----------------------+--------------------------------------------------+ | H.Encaps.PREOF.L2.Red | H.Encaps.PREOF.Red Applied to Received L2 Frames | +-----------------------+--------------------------------------------------+ Figure 2: PREOF specific SR Policy Headend Behaviors 5.1. H.Encaps.PREOF: SR Headend with PREOF When a node "N" receives a packet P=(A, B) identified as a DetNet Flow. B is neither a local address nor SID of "N". It executes the DetNet Flow related PREOF function(s), resulting in one or more member flow (P1=(A, B), P2=(A, B), ...) with related parameters ([Flow-ID1, SeqNum], [Flow-ID2, SeqNum], ...). Varga & Fejes Expires 21 June 2025 [Page 5] Internet-Draft PREOF SID December 2024 Node "N" is configured with an IPv6 address "T" (e.g., assigned to its loopback). "N" steers the egress packet P1 into an SRv6 Policy with a Source Address T and a segment list SP1=, where S13 is a DetNet-specific SID (LOC+FUNCT) with 0 as ARG. The H.Encaps.PREOF encapsulation behavior is defined as follows (SA: source address, DA: destination address): S01. Push an IPv6 header with its own SRH Set the ARG part of the LAST SID in the segment list S02. Set outer IPv6 SA = T and outer IPv6 DA to the first SID in the segment list S03. Set outer Payload Length, Traffic Class, Hop Limit, and Flow Label fields S04. Set the outer Next Header value S05. Decrement inner IPv6 Hop Limit or IPv4 TTL S06. Submit the packet to the IPv6 module for transmission to S11 After the H.Encaps.PREOF behavior, P1, and P2 respectively look like: * (T, S11) (S13, S12, S11; SL=2) (A, B), note: S13.ARG=Flow-ID1, SeqNum * (T, S21) (S23, S22, S21; SL=2) (A, B), note: S23.ARG=Flow-ID2, SeqNum The member flow packet is encapsulated unmodified (with the exception of the IPv4 TTL or IPv6 Hop Limit that is decremented). The push of the SRH MAY be omitted when the SRv6 Policy only contains one segment and there is no need to use any flag, tag, or TLV. In such cases the outer destination address is the DetNet-specific SID. 5.2. H.Encaps.PREOF.Red: H.Encaps.PREOF with Reduced Encapsulation The H.Encaps.PREOF.Red behavior is an optimization of the H.Encaps.PREOF behavior. H.Encaps.PREOF.Red reduces the length of the SRH by excluding the first SID in the SRH of the pushed IPv6 header. The first SID is only placed in the Destination Address field of the pushed IPv6 header. After the H.Encaps.PREOF.Red behavior, P1, and P2 respectively look like: * (T, S11) (S13, S12; SL=2) (A, B), note: S13.ARG=Flow-ID1, SeqNum Varga & Fejes Expires 21 June 2025 [Page 6] Internet-Draft PREOF SID December 2024 * (T, S21) (S23, S22; SL=2) (A, B), note: S23.ARG=Flow-ID2, SeqNum 5.3. H.Encaps.PREOF.L2: H.Encaps.PREOF Applied to Received L2 Frames The H.Encaps.PREOF.L2 behavior encapsulates a received Ethernet frame and its attached VLAN header, if present, in an IPv6 packet with an SRH. The Ethernet frame becomes the payload of the new IPv6 packet. The H.Encaps.PREOF.L2 encapsulation behavior is similar to H.Encaps.PREOF but sets an Ethernet specific outer Next Header and lacks the TTL/Hop Limit related action. H.Encaps.PREOF.L2 is defined as follows: S01. Push an IPv6 header with its own SRH Set the ARG part of the LAST SID in the segment list S02. Set outer IPv6 SA = T and outer IPv6 DA to the first SID in the segment list S03. Set outer Payload Length, Traffic Class, Hop Limit, and Flow Label fields S04. Set the outer Next Header value S05. S06. Submit the packet to the IPv6 module for transmission to S11 The Next Header field of the SRH MUST be set to 143. The push of the SRH MAY be omitted when the SRv6 Policy only contains one segment and there is no need to use any flag, tag, or TLV. The encapsulating node MUST remove the preamble (if any) and frame check sequence (FCS) from the Ethernet frame upon encapsulation, and the decapsulating node MUST regenerate, as required, the preamble and FCS before forwarding the Ethernet frame. 5.4. H.Encaps.PREOF.L2.Red: H.Encaps.PREOF.L2 with Reduced Encapsulation The H.Encaps.PREOF.L2.Red behavior is an optimization of the H.Encaps.PREOF.L2 behavior. H.Encaps.PREOF.L2.Red reduces the length of the SRH by excluding the first SID in the SRH of the pushed IPv6 header. The first SID is only placed in the Destination Address field of the pushed IPv6 header. The push of the SRH MAY be omitted when the SRv6 Policy only contains one segment and there is no need to use any flag, tag, or TLV. Varga & Fejes Expires 21 June 2025 [Page 7] Internet-Draft PREOF SID December 2024 6. DetNet-specific SID related counters PREOF implementation may provide counters per DetNet flow. However, in order to be inline with the intention of RFC8986 (section 6. Counters), its recommendation may apply on the DetNet-specific SID and the above described set of SR Behaviors. It means, a node supporting DetNet-specific SID should implement a pair of traffic counters (one for packets and one for bytes) per local SID entry, for traffic that matched that SID and was processed successfully (i.e., packets that generate ICMP Error Messages or are dropped are not counted). The retrieval of these counters from MIB, NETCONF/YANG, or any other data structure is outside the scope of this document. 7. Security Considerations DetNet PREOF related security considerations are described in section 3.3 of [RFC9055]. There are no additional related security considerations originating from this document. SRv6 Network Programming related security considerations are described in section 9 of [RFC8986]. There are no additional related security considerations originating from this document. 8. IANA Considerations This document requires registration of End.DPREOF behavior in "SRv6 Endpoint Behaviors" sub-registry of "Segment Routing Parameters" registry. IANA is requested to make one new assignments from the First Come First Served portion of the registry as follows: Value | Hex | Endpoint Behavior | Reference | Change Controller ------+-------+-------------------+------------+------------------ TBD1 | xTBD1 | End.DPREOF | [This.I-D] | IETF 9. Acknowledgements Authors extend their appreciation to Janos Farkas, Istvan Moldovan and Miklos Mate for their insightful comments and productive discussion that helped to improve the document. 10. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . Varga & Fejes Expires 21 June 2025 [Page 8] Internet-Draft PREOF SID December 2024 [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC8402] Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L., Decraene, B., Litkowski, S., and R. Shakir, "Segment Routing Architecture", RFC 8402, DOI 10.17487/RFC8402, July 2018, . [RFC8655] Finn, N., Thubert, P., Varga, B., and J. Farkas, "Deterministic Networking Architecture", RFC 8655, DOI 10.17487/RFC8655, October 2019, . [RFC8964] Varga, B., Ed., Farkas, J., Berger, L., Malis, A., Bryant, S., and J. Korhonen, "Deterministic Networking (DetNet) Data Plane: MPLS", RFC 8964, DOI 10.17487/RFC8964, January 2021, . [RFC8986] Filsfils, C., Ed., Camarillo, P., Ed., Leddy, J., Voyer, D., Matsushima, S., and Z. Li, "Segment Routing over IPv6 (SRv6) Network Programming", RFC 8986, DOI 10.17487/RFC8986, February 2021, . [RFC9055] Grossman, E., Ed., Mizrahi, T., and A. Hacker, "Deterministic Networking (DetNet) Security Considerations", RFC 9055, DOI 10.17487/RFC9055, June 2021, . Authors' Addresses Balazs Varga (editor) Ericsson Budapest Magyar Tudosok krt. 11. 1117 Hungary Email: balazs.a.varga@ericsson.com Ferenc Fejes Ericsson Budapest Magyar Tudosok krt. 11. 1117 Hungary Email: ferenc.fejes@ericsson.com Varga & Fejes Expires 21 June 2025 [Page 9]