Network Working Group T. Ylonen Request for Comments: 4251 SSH Communications Security Corp Category: Standards Track C. Lonvick, Ed. Cisco Systems, Inc. January 2006 The Secure Shell (SSH) Protocol Architecture Status of This Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Copyright Notice Copyright (C) The Internet Society (2006). Abstract The Secure Shell (SSH) Protocol is a protocol for secure remote login and other secure network services over an insecure network. This document describes the architecture of the SSH protocol, as well as the notation and terminology used in SSH protocol documents. It also discusses the SSH algorithm naming system that allows local extensions. The SSH protocol consists of three major components: The Transport Layer Protocol provides server authentication, confidentiality, and integrity with perfect forward secrecy. The User Authentication Protocol authenticates the client to the server. The Connection Protocol multiplexes the encrypted tunnel into several logical channels. Details of these protocols are described in separate documents. Ylonen & Lonvick Standards Track [Page 1] RFC 4251 SSH Protocol Architecture January 2006 Table of Contents 1. Introduction ....................................................3 2. Contributors ....................................................3 3. Conventions Used in This Document ...............................4 4. Architecture ....................................................4 4.1. Host Keys ..................................................4 4.2. Extensibility ..............................................6 4.3. Policy Issues ..............................................6 4.4. Security Properties ........................................7 4.5. Localization and Character Set Support .....................7 5. Data Type Representations Used in the SSH Protocols .............8 6. Algorithm and Method Naming ....................................10 7. Message Numbers ................................................11 8. IANA Considerations ............................................12 9. Security Considerations ........................................13 9.1. Pseudo-Random Number Generation ...........................13 9.2. Control Character Filtering ...............................14 9.3. Transport .................................................14 9.3.1. Confidentiality ....................................14 9.3.2. Data Integrity .....................................16 9.3.3. Replay .............................................16 9.3.4. Man-in-the-middle ..................................17 9.3.5. Denial of Service ..................................19 9.3.6. Covert Channels ....................................20 9.3.7. Forward Secrecy ....................................20 9.3.8. Ordering of Key Exchange Methods ...................20 9.3.9. Traffic Analysis ...................................21 9.4. Authentication Protocol ...................................21 9.4.1. Weak Transport .....................................21 9.4.2. Debug Messages .....................................22 9.4.3. Local Security Policy ..............................22 9.4.4. Public Key Authentication ..........................23 9.4.5. Password Authentication ............................23 9.4.6. Host-Based Authentication ..........................23 9.5. Connection Protocol .......................................24 9.5.1. End Point Security .................................24 9.5.2. Proxy Forwarding ...................................24 9.5.3. X11 Forwarding .....................................24 10. References ....................................................26 10.1. Normative References .....................................26 10.2. Informative References ...................................26 Authors' Addresses ................................................29 Trademark Notice ..................................................29 Ylonen & Lonvick Standards Track [Page 2] RFC 4251 SSH Protocol Architecture January 2006 1. Introduction Secure Shell (SSH) is a protocol for secure remote login and other secure network services over an insecure network. It consists of three major components: o The Transport Layer Protocol [SSH-TRANS] provides server authentication, confidentiality, and integrity. It may optionally also provide compression. The transport layer will typically be run over a TCP/IP connection, but might also be used on top of any other reliable data stream. o The User Authentication Protocol [SSH-USERAUTH] authenticates the client-side user to the server. It runs over the transport layer protocol. o The Connection Protocol [SSH-CONNECT] multiplexes the encrypted tunnel into several logical channels. It runs over the user authentication protocol. The client sends a service request once a secure transport layer connection has been established. A second service request is sent after user authentication is complete. This allows new protocols to be defined and coexist with the protocols listed above. The connection protocol provides channels that can be used for a wide range of purposes. Standard methods are provided for setting up secure interactive shell sessions and for forwarding ("tunneling") arbitrary TCP/IP ports and X11 connections. 2. Contributors The major original contributors of this set of documents have been: Tatu Ylonen, Tero Kivinen, Timo J. Rinne, Sami Lehtinen (all of SSH Communications Security Corp), and Markku-Juhani O. Saarinen (University of Jyvaskyla). Darren Moffat was the original editor of this set of documents and also made very substantial contributions. Many people contributed to the development of this document over the years. People who should be acknowledged include Mats Andersson, Ben Harris, Bill Sommerfeld, Brent McClure, Niels Moller, Damien Miller, Derek Fawcus, Frank Cusack, Heikki Nousiainen, Jakob Schlyter, Jeff Van Dyke, Jeffrey Altman, Jeffrey Hutzelman, Jon Bright, Joseph Galbraith, Ken Hornstein, Markus Friedl, Martin Forssen, Nicolas Williams, Niels Provos, Perry Metzger, Peter Gutmann, Simon Josefsson, Simon Tatham, Wei Dai, Denis Bider, der Mouse, and Tadayoshi Kohno. Listing their names here does not mean that they endorse this document, but that they have contributed to it. Ylonen & Lonvick Standards Track [Page 3] RFC 4251 SSH Protocol Architecture January 2006 3. Conventions Used in This Document All documents related to the SSH protocols shall use the keywords "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" to describe requirements. These keywords are to be interpreted as described in [RFC2119]. The keywords "PRIVATE USE", "HIERARCHICAL ALLOCATION", "FIRST COME FIRST SERVED", "EXPERT REVIEW", "SPECIFICATION REQUIRED", "IESG APPROVAL", "IETF CONSENSUS", and "STANDARDS ACTION" that appear in this document when used to describe namespace allocation are to be interpreted as described in [RFC2434]. Protocol fields and possible values to fill them are defined in this set of documents. Protocol fields will be defined in the message definitions. As an example, SSH_MSG_CHANNEL_DATA is defined as follows. byte SSH_MSG_CHANNEL_DATA uint32 recipient channel string data Throughout these documents, when the fields are referenced, they will appear within single quotes. When values to fill those fields are referenced, they will appear within double quotes. Using the above example, possible values for 'data' are "foo" and "bar". 4. Architecture 4.1. Host Keys Each server host SHOULD have a host key. Hosts MAY have multiple host keys using multiple different algorithms. Multiple hosts MAY share the same host key. If a host has keys at all, it MUST have at least one key that uses each REQUIRED public key algorithm (DSS [FIPS-186-2]). The server host key is used during key exchange to verify that the client is really talking to the correct server. For this to be possible, the client must have a priori knowledge of the server's public host key. Two different trust models can be used: o The client has a local database that associates each host name (as typed by the user) with the corresponding public host key. This method requires no centrally administered infrastructure, and no Ylonen & Lonvick Standards Track [Page 4] RFC 4251 SSH Protocol Architecture January 2006 third-party coordination. The downside is that the database of name-to-key associations may become burdensome to maintain. o The host name-to-key association is certified by a trusted certification authority (CA). The client only knows the CA root key, and can verify the validity of all host keys certified by accepted CAs. The second alternative eases the maintenance problem, since ideally only a single CA key needs to be securely stored on the client. On the other hand, each host key must be appropriately certified by a central authority before authorization is possible. Also, a lot of trust is placed on the central infrastructure. The protocol provides the option that the server name - host key association is not checked when connecting to the host for the first time. This allows communication without prior communication of host keys or certification. The connection still provides protection against passive listening; however, it becomes vulnerable to active man-in-the-middle attacks. Implementations SHOULD NOT normally allow such connections by default, as they pose a potential security problem. However, as there is no widely deployed key infrastructure available on the Internet at the time of this writing, this option makes the protocol much more usable during the transition time until such an infrastructure emerges, while still providing a much higher level of security than that offered by older solutions (e.g., telnet [RFC0854] and rlogin [RFC1282]). Implementations SHOULD try to make the best effort to check host keys. An example of a possible strategy is to only accept a host key without checking the first time a host is connected, save the key in a local database, and compare against that key on all future connections to that host. Implementations MAY provide additional methods for verifying the correctness of host keys, e.g., a hexadecimal fingerprint derived from the SHA-1 hash [FIPS-180-2] of the public key. Such fingerprints can easily be verified by using telephone or other external communication channels. All implementations SHOULD provide an option not to accept host keys that cannot be verified. The members of this Working Group believe that 'ease of use' is critical to end-user acceptance of security solutions, and no improvement in security is gained if the new solutions are not used. Thus, providing the option not to check the server host key is Ylonen & Lonvick Standards Track [Page 5] RFC 4251 SSH Protocol Architecture January 2006 believed to improve the overall security of the Internet, even though it reduces the security of the protocol in configurations where it is allowed. 4.2. Extensibility We believe that the protocol will evolve over time, and some organizations will want to use their own encryption, authentication, and/or key exchange methods. Central registration of all extensions is cumbersome, especially for experimental or classified features. On the other hand, having no central registration leads to conflicts in method identifiers, making interoperability difficult. We have chosen to identify algorithms, methods, formats, and extension protocols with textual names that are of a specific format. DNS names are used to create local namespaces where experimental or classified extensions can be defined without fear of conflicts with other implementations. One design goal has been to keep the base protocol as simple as possible, and to require as few algorithms as possible. However, all implementations MUST support a minimal set of algorithms to ensure interoperability (this does not imply that the local policy on all hosts would necessarily allow these algorithms). The mandatory algorithms are specified in the relevant protocol documents. Additional algorithms, methods, formats, and extension protocols can be defined in separate documents. See Section 6, Algorithm Naming, for more information. 4.3. Policy Issues The protocol allows full negotiation of encryption, integrity, key exchange, compression, and public key algorithms and formats. Encryption, integrity, public key, and compression algorithms can be different for each direction. The following policy issues SHOULD be addressed in the configuration mechanisms of each implementation: o Encryption, integrity, and compression algorithms, separately for each direction. The policy MUST specify which is the preferred algorithm (e.g., the first algorithm listed in each category). o Public key algorithms and key exchange method to be used for host authentication. The existence of trusted host keys for different public key algorithms also affects this choice. Ylonen & Lonvick Standards Track [Page 6] RFC 4251 SSH Protocol Architecture January 2006 o The authentication methods that are to be required by the server for each user. The server's policy MAY require multiple authentication for some or all users. The required algorithms MAY depend on the location from where the user is trying to gain access. o The operations that the user is allowed to perform using the connection protocol. Some issues are related to security; for example, the policy SHOULD NOT allow the server to start sessions or run commands on the client machine, and MUST NOT allow connections to the authentication agent unless forwarding such connections has been requested. Other issues, such as which TCP/IP ports can be forwarded and by whom, are clearly issues of local policy. Many of these issues may involve traversing or bypassing firewalls, and are interrelated with the local security policy. 4.4. Security Properties The primary goal of the SSH protocol is to improve security on the Internet. It attempts to do this in a way that is easy to deploy, even at the cost of absolute security. o All encryption, integrity, and public key algorithms used are well-known, well-established algorithms. o All algorithms are used with cryptographically sound key sizes that are believed to provide protection against even the strongest cryptanalytic attacks for decades. o All algorithms are negotiated, and in case some algorithm is broken, it is easy to switch to some other algorithm without modifying the base protocol. Specific concessions were made to make widespread, fast deployment easier. The particular case where this comes up is verifying that the server host key really belongs to the desired host; the protocol allows the verification to be left out, but this is NOT RECOMMENDED. This is believed to significantly improve usability in the short term, until widespread Internet public key infrastructures emerge. 4.5. Localization and Character Set Support For the most part, the SSH protocols do not directly pass text that would be displayed to the user. However, there are some places where such data might be passed. When applicable, the character set for Ylonen & Lonvick Standards Track [Page 7] RFC 4251 SSH Protocol Architecture January 2006 the data MUST be explicitly specified. In most places, ISO-10646 UTF-8 encoding is used [RFC3629]. When applicable, a field is also provided for a language tag [RFC3066]. One big issue is the character set of the interactive session. There is no clear solution, as different applications may display data in different formats. Different types of terminal emulation may also be employed in the client, and the character set to be used is effectively determined by the terminal emulation. Thus, no place is provided for directly specifying the character set or encoding for terminal session data. However, the terminal emulation type (e.g., "vt100") is transmitted to the remote site, and it implicitly specifies the character set and encoding. Applications typically use the terminal type to determine what character set they use, or the character set is determined using some external means. The terminal emulation may also allow configuring the default character set. In any case, the character set for the terminal session is considered primarily a client local issue. Internal names used to identify algorithms or protocols are normally never displayed to users, and must be in US-ASCII. The client and server user names are inherently constrained by what the server is prepared to accept. They might, however, occasionally be displayed in logs, reports, etc. They MUST be encoded using ISO 10646 UTF-8, but other encodings may be required in some cases. It is up to the server to decide how to map user names to accepted user names. Straight bit-wise, binary comparison is RECOMMENDED. For localization purposes, the protocol attempts to minimize the number of textual messages transmitted. When present, such messages typically relate to errors, debugging information, or some externally configured data. For data that is normally displayed, it SHOULD be possible to fetch a localized message instead of the transmitted message by using a numerical code. The remaining messages SHOULD be configurable. 5. Data Type Representations Used in the SSH Protocols byte A byte represents an arbitrary 8-bit value (octet). Fixed length data is sometimes represented as an array of bytes, written byte[n], where n is the number of bytes in the array. Ylonen & Lonvick Standards Track [Page 8] RFC 4251 SSH Protocol Architecture January 2006 boolean A boolean value is stored as a single byte. The value 0 represents FALSE, and the value 1 represents TRUE. All non-zero values MUST be interpreted as TRUE; however, applications MUST NOT store values other than 0 and 1. uint32 Represents a 32-bit unsigned integer. Stored as four bytes in the order of decreasing significance (network byte order). For example: the value 699921578 (0x29b7f4aa) is stored as 29 b7 f4 aa. uint64 Represents a 64-bit unsigned integer. Stored as eight bytes in the order of decreasing significance (network byte order). string Arbitrary length binary string. Strings are allowed to contain arbitrary binary data, including null characters and 8-bit characters. They are stored as a uint32 containing its length (number of bytes that follow) and zero (= empty string) or more bytes that are the value of the string. Terminating null characters are not used. Strings are also used to store text. In that case, US-ASCII is used for internal names, and ISO-10646 UTF-8 for text that might be displayed to the user. The terminating null character SHOULD NOT normally be stored in the string. For example: the US-ASCII string "testing" is represented as 00 00 00 07 t e s t i n g. The UTF-8 mapping does not alter the encoding of US-ASCII characters. mpint Represents multiple precision integers in two's complement format, stored as a string, 8 bits per byte, MSB first. Negative numbers have the value 1 as the most significant bit of the first byte of the data partition. If the most significant bit would be set for a positive number, the number MUST be preceded by a zero byte. Unnecessary leading bytes with the value 0 or 255 MUST NOT be included. The value zero MUST be stored as a string with zero bytes of data. By convention, a number that is used in modular computations in Z_n SHOULD be represented in the range 0 <= x < n. Ylonen & Lonvick Standards Track [Page 9] RFC 4251 SSH Protocol Architecture January 2006 Examples: value (hex) representation (hex) ----------- -------------------- 0 00 00 00 00 9a378f9b2e332a7 00 00 00 08 09 a3 78 f9 b2 e3 32 a7 80 00 00 00 02 00 80 -1234 00 00 00 02 ed cc -deadbeef 00 00 00 05 ff 21 52 41 11 name-list A string containing a comma-separated list of names. A name-list is represented as a uint32 containing its length (number of bytes that follow) followed by a comma-separated list of zero or more names. A name MUST have a non-zero length, and it MUST NOT contain a comma (","). As this is a list of names, all of the elements contained are names and MUST be in US-ASCII. Context may impose additional restrictions on the names. For example, the names in a name-list may have to be a list of valid algorithm identifiers (see Section 6 below), or a list of [RFC3066] language tags. The order of the names in a name-list may or may not be significant. Again, this depends on the context in which the list is used. Terminating null characters MUST NOT be used, neither for the individual names, nor for the list as a whole. Examples: value representation (hex) ----- -------------------- (), the empty name-list 00 00 00 00 ("zlib") 00 00 00 04 7a 6c 69 62 ("zlib,none") 00 00 00 09 7a 6c 69 62 2c 6e 6f 6e 65 6. Algorithm and Method Naming The SSH protocols refer to particular hash, encryption, integrity, compression, and key exchange algorithms or methods by name. There are some standard algorithms and methods that all implementations MUST support. There are also algorithms and methods that are defined in the protocol specification, but are OPTIONAL. Furthermore, it is expected that some organizations will want to use their own algorithms or methods. In this protocol, all algorithm and method identifiers MUST be printable US-ASCII, non-empty strings no longer than 64 characters. Names MUST be case-sensitive. Ylonen & Lonvick Standards Track [Page 10] RFC 4251 SSH Protocol Architecture January 2006 There are two formats for algorithm and method names: o Names that do not contain an at-sign ("@") are reserved to be assigned by IETF CONSENSUS. Examples include "3des-cbc", "sha-1", "hmac-sha1", and "zlib" (the doublequotes are not part of the name). Names of this format are only valid if they are first registered with the IANA. Registered names MUST NOT contain an at-sign ("@"), comma (","), whitespace, control characters (ASCII codes 32 or less), or the ASCII code 127 (DEL). Names are case- sensitive, and MUST NOT be longer than 64 characters. o Anyone can define additional algorithms or methods by using names in the format name@domainname, e.g., "ourcipher-cbc@example.com". The format of the part preceding the at-sign is not specified; however, these names MUST be printable US-ASCII strings, and MUST NOT contain the comma character (","), whitespace, control characters (ASCII codes 32 or less), or the ASCII code 127 (DEL). They MUST have only a single at-sign in them. The part following the at-sign MUST be a valid, fully qualified domain name [RFC1034] controlled by the person or organization defining the name. Names are case-sensitive, and MUST NOT be longer than 64 characters. It is up to each domain how it manages its local namespace. It should be noted that these names resemble STD 11 [RFC0822] email addresses. This is purely coincidental and has nothing to do with STD 11 [RFC0822]. 7. Message Numbers SSH packets have message numbers in the range 1 to 255. These numbers have been allocated as follows: Transport layer protocol: 1 to 19 Transport layer generic (e.g., disconnect, ignore, debug, etc.) 20 to 29 Algorithm negotiation 30 to 49 Key exchange method specific (numbers can be reused for different authentication methods) User authentication protocol: 50 to 59 User authentication generic 60 to 79 User authentication method specific (numbers can be reused for different authentication methods) Ylonen & Lonvick Standards Track [Page 11] RFC 4251 SSH Protocol Architecture January 2006 Connection protocol: 80 to 89 Connection protocol generic 90 to 127 Channel related messages Reserved for client protocols: 128 to 191 Reserved Local extensions: 192 to 255 Local extensions 8. IANA Considerations This document is part of a set. The instructions for the IANA for the SSH protocol, as defined in this document, [SSH-USERAUTH], [SSH-TRANS], and [SSH-CONNECT], are detailed in [SSH-NUMBERS]. The following is a brief summary for convenience, but note well that [SSH-NUMBERS] contains the actual instructions to the IANA, which may be superseded in the future. Allocation of the following types of names in the SSH protocols is assigned by IETF consensus: o Service Names * Authentication Methods * Connection Protocol Channel Names * Connection Protocol Global Request Names * Connection Protocol Channel Request Names o Key Exchange Method Names o Assigned Algorithm Names * Encryption Algorithm Names * MAC Algorithm Names * Public Key Algorithm Names * Compression Algorithm Names These names MUST be printable US-ASCII strings, and MUST NOT contain the characters at-sign ("@"), comma (","), whitespace, control characters (ASCII codes 32 or less), or the ASCII code 127 (DEL). Names are case-sensitive, and MUST NOT be longer than 64 characters. Names with the at-sign ("@") are locally defined extensions and are not controlled by the IANA. Ylonen & Lonvick Standards Track [Page 12] RFC 4251 SSH Protocol Architecture January 2006 Each category of names listed above has a separate namespace. However, using the same name in multiple categories SHOULD be avoided to minimize confusion. Message numbers (see Section 7) in the range of 0 to 191 are allocated via IETF CONSENSUS, as described in [RFC2434]. Message numbers in the 192 to 255 range (local extensions) are reserved for PRIVATE USE, also as described in [RFC2434]. 9. Security Considerations In order to make the entire body of Security Considerations more accessible, Security Considerations for the transport, authentication, and connection documents have been gathered here. The transport protocol [SSH-TRANS] provides a confidential channel over an insecure network. It performs server host authentication, key exchange, encryption, and integrity protection. It also derives a unique session id that may be used by higher-level protocols. The authentication protocol [SSH-USERAUTH] provides a suite of mechanisms that can be used to authenticate the client user to the server. Individual mechanisms specified in the authentication protocol use the session id provided by the transport protocol and/or depend on the security and integrity guarantees of the transport protocol. The connection protocol [SSH-CONNECT] specifies a mechanism to multiplex multiple streams (channels) of data over the confidential and authenticated transport. It also specifies channels for accessing an interactive shell, for proxy-forwarding various external protocols over the secure transport (including arbitrary TCP/IP protocols), and for accessing secure subsystems on the server host. 9.1. Pseudo-Random Number Generation This protocol binds each session key to the session by including random, session specific data in the hash used to produce session keys. Special care should be taken to ensure that all of the random numbers are of good quality. If the random data here (e.g., Diffie- Hellman (DH) parameters) are pseudo-random, then the pseudo-random number generator should be cryptographically secure (i.e., its next output not easily guessed even when knowing all previous outputs) and, furthermore, proper entropy needs to be added to the pseudo- random number generator. [RFC4086] offers suggestions for sources of random numbers and entropy. Implementers should note the importance of entropy and the well-meant, anecdotal warning about the difficulty in properly implementing pseudo-random number generating functions. Ylonen & Lonvick Standards Track [Page 13] RFC 4251 SSH Protocol Architecture January 2006 The amount of entropy available to a given client or server may sometimes be less than what is required. In this case, one must either resort to pseudo-random number generation regardless of insufficient entropy or refuse to run the protocol. The latter is preferable. 9.2. Control Character Filtering When displaying text to a user, such as error or debug messages, the client software SHOULD replace any control characters (except tab, carriage return, and newline) with safe sequences to avoid attacks by sending terminal control characters. 9.3. Transport 9.3.1. Confidentiality It is beyond the scope of this document and the Secure Shell Working Group to analyze or recommend specific ciphers other than the ones that have been established and accepted within the industry. At the time of this writing, commonly used ciphers include 3DES, ARCFOUR, twofish, serpent, and blowfish. AES has been published by The US Federal Information Processing Standards as [FIPS-197], and the cryptographic community has accepted AES as well. As always, implementers and users should check current literature to ensure that no recent vulnerabilities have been found in ciphers used within products. Implementers should also check to see which ciphers are considered to be relatively stronger than others and should recommend their use to users over relatively weaker ciphers. It would be considered good form for an implementation to politely and unobtrusively notify a user that a stronger cipher is available and should be used when a weaker one is actively chosen. The "none" cipher is provided for debugging and SHOULD NOT be used except for that purpose. Its cryptographic properties are sufficiently described in [RFC2410], which will show that its use does not meet the intent of this protocol. The relative merits of these and other ciphers may also be found in current literature. Two references that may provide information on the subject are [SCHNEIER] and [KAUFMAN]. Both of these describe the CBC mode of operation of certain ciphers and the weakness of this scheme. Essentially, this mode is theoretically vulnerable to chosen cipher-text attacks because of the high predictability of the start of packet sequence. However, this attack is deemed difficult and not considered fully practicable, especially if relatively long block sizes are used. Ylonen & Lonvick Standards Track [Page 14] RFC 4251 SSH Protocol Architecture January 2006 Additionally, another CBC mode attack may be mitigated through the insertion of packets containing SSH_MSG_IGNORE. Without this technique, a specific attack may be successful. For this attack (commonly known as the Rogaway attack [ROGAWAY], [DAI], [BELLARE]) to work, the attacker would need to know the Initialization Vector (IV) of the next block that is going to be encrypted. In CBC mode that is the output of the encryption of the previous block. If the attacker does not have any way to see the packet yet (i.e., it is in the internal buffers of the SSH implementation or even in the kernel), then this attack will not work. If the last packet has been sent out to the network (i.e., the attacker has access to it), then he can use the attack. In the optimal case, an implementer would need to add an extra packet only if the packet has been sent out onto the network and there are no other packets waiting for transmission. Implementers may wish to check if there are any unsent packets awaiting transmission; unfortunately, it is not normally easy to obtain this information from the kernel or buffers. If there are no unsent packets, then a packet containing SSH_MSG_IGNORE SHOULD be sent. If a new packet is added to the stream every time the attacker knows the IV that is supposed to be used for the next packet, then the attacker will not be able to guess the correct IV, thus the attack will never be successful. As an example, consider the following case: Client Server ------ ------ TCP(seq=x, len=500) ----> contains Record 1 [500 ms passes, no ACK] TCP(seq=x, len=1000) ----> contains Records 1,2 ACK 1. The Nagle algorithm + TCP retransmits mean that the two records get coalesced into a single TCP segment. 2. Record 2 is not at the beginning of the TCP segment and never will be because it gets ACKed. 3. Yet, the attack is possible because Record 1 has already been seen. Ylonen & Lonvick Standards Track [Page 15] RFC 4251 SSH Protocol Architecture January 2006 As this example indicates, it is unsafe to use the existence of unflushed data in the TCP buffers proper as a guide to whether an empty packet is needed, since when the second write() is performed the buffers will contain the un-ACKed Record 1. On the other hand, it is perfectly safe to have the following situation: Client Server ------ ------ TCP(seq=x, len=500) ----> contains SSH_MSG_IGNORE TCP(seq=y, len=500) ----> contains Data Provided that the IV for the second SSH Record is fixed after the data for the Data packet is determined, then the following should be performed: read from user encrypt null packet encrypt data packet 9.3.2. Data Integrity This protocol does allow the Data Integrity mechanism to be disabled. Implementers SHOULD be wary of exposing this feature for any purpose other than debugging. Users and administrators SHOULD be explicitly warned anytime the "none" MAC is enabled. So long as the "none" MAC is not used, this protocol provides data integrity. Because MACs use a 32-bit sequence number, they might start to leak information after 2**32 packets have been sent. However, following the rekeying recommendations should prevent this attack. The transport protocol [SSH-TRANS] recommends rekeying after one gigabyte of data, and the smallest possible packet is 16 bytes. Therefore, rekeying SHOULD happen after 2**28 packets at the very most. 9.3.3. Replay The use of a MAC other than "none" provides integrity and authentication. In addition, the transport protocol provides a unique session identifier (bound in part to pseudo-random data that is part of the algorithm and key exchange process) that can be used by higher level protocols to bind data to a given session and prevent Ylonen & Lonvick Standards Track [Page 16] RFC 4251 SSH Protocol Architecture January 2006 replay of data from prior sessions. For example, the authentication protocol ([SSH-USERAUTH]) uses this to prevent replay of signatures from previous sessions. Because public key authentication exchanges are cryptographically bound to the session (i.e., to the initial key exchange), they cannot be successfully replayed in other sessions. Note that the session id can be made public without harming the security of the protocol. If two sessions have the same session id (hash of key exchanges), then packets from one can be replayed against the other. It must be stressed that the chances of such an occurrence are, needless to say, minimal when using modern cryptographic methods. This is all the more true when specifying larger hash function outputs and DH parameters. Replay detection using monotonically increasing sequence numbers as input to the MAC, or HMAC in some cases, is described in [RFC2085], [RFC2246], [RFC2743], [RFC1964], [RFC2025], and [RFC4120]. The underlying construct is discussed in [RFC2104]. Essentially, a different sequence number in each packet ensures that at least this one input to the MAC function will be unique and will provide a nonrecurring MAC output that is not predictable to an attacker. If the session stays active long enough, however, this sequence number will wrap. This event may provide an attacker an opportunity to replay a previously recorded packet with an identical sequence number but only if the peers have not rekeyed since the transmission of the first packet with that sequence number. If the peers have rekeyed, then the replay will be detected since the MAC check will fail. For this reason, it must be emphasized that peers MUST rekey before a wrap of the sequence numbers. Naturally, if an attacker does attempt to replay a captured packet before the peers have rekeyed, then the receiver of the duplicate packet will not be able to validate the MAC and it will be discarded. The reason that the MAC will fail is because the receiver will formulate a MAC based upon the packet contents, the shared secret, and the expected sequence number. Since the replayed packet will not be using that expected sequence number (the sequence number of the replayed packet will have already been passed by the receiver), the calculated MAC will not match the MAC received with the packet. 9.3.4. Man-in-the-middle This protocol makes no assumptions or provisions for an infrastructure or means for distributing the public keys of hosts. It is expected that this protocol will sometimes be used without first verifying the association between the server host key and the server host name. Such usage is vulnerable to man-in-the-middle attacks. This section describes this and encourages administrators Ylonen & Lonvick Standards Track [Page 17] RFC 4251 SSH Protocol Architecture January 2006 and users to understand the importance of verifying this association before any session is initiated. There are three cases of man-in-the-middle attacks to consider. The first is where an attacker places a device between the client and the server before the session is initiated. In this case, the attack device is trying to mimic the legitimate server and will offer its public key to the client when the client initiates a session. If it were to offer the public key of the server, then it would not be able to decrypt or sign the transmissions between the legitimate server and the client unless it also had access to the private key of the host. The attack device will also, simultaneously to this, initiate a session to the legitimate server, masquerading itself as the client. If the public key of the server had been securely distributed to the client prior to that session initiation, the key offered to the client by the attack device will not match the key stored on the client. In that case, the user SHOULD be given a warning that the offered host key does not match the host key cached on the client. As described in Section 4.1, the user may be free to accept the new key and continue the session. It is RECOMMENDED that the warning provide sufficient information to the user of the client device so the user may make an informed decision. If the user chooses to continue the session with the stored public key of the server (not the public key offered at the start of the session), then the session-specific data between the attacker and server will be different between the client-to-attacker session and the attacker- to-server sessions due to the randomness discussed above. From this, the attacker will not be able to make this attack work since the attacker will not be able to correctly sign packets containing this session-specific data from the server, since he does not have the private key of that server. The second case that should be considered is similar to the first case in that it also happens at the time of connection, but this case points out the need for the secure distribution of server public keys. If the server public keys are not securely distributed, then the client cannot know if it is talking to the intended server. An attacker may use social engineering techniques to pass off server keys to unsuspecting users and may then place a man-in-the-middle attack device between the legitimate server and the clients. If this is allowed to happen, then the clients will form client-to-attacker sessions, and the attacker will form attacker-to-server sessions and will be able to monitor and manipulate all of the traffic between the clients and the legitimate servers. Server administrators are encouraged to make host key fingerprints available for checking by some means whose security does not rely on the integrity of the actual host keys. Possible mechanisms are discussed in Section 4.1 and may also include secured Web pages, physical pieces of paper, Ylonen & Lonvick Standards Track [Page 18] RFC 4251 SSH Protocol Architecture January 2006 etc. Implementers SHOULD provide recommendations on how best to do this with their implementation. Because the protocol is extensible, future extensions to the protocol may provide better mechanisms for dealing with the need to know the server's host key before connecting. For example, making the host key fingerprint available through a secure DNS lookup, or using Kerberos ([RFC4120]) over GSS-API ([RFC1964]) during key exchange to authenticate the server are possibilities. In the third man-in-the-middle case, attackers may attempt to manipulate packets in transit between peers after the session has been established. As described in Section 9.3.3, a successful attack of this nature is very improbable. As in Section 9.3.3, this reasoning does assume that the MAC is secure and that it is infeasible to construct inputs to a MAC algorithm to give a known output. This is discussed in much greater detail in Section 6 of [RFC2104]. If the MAC algorithm has a vulnerability or is weak enough, then the attacker may be able to specify certain inputs to yield a known MAC. With that, they may be able to alter the contents of a packet in transit. Alternatively, the attacker may be able to exploit the algorithm vulnerability or weakness to find the shared secret by reviewing the MACs from captured packets. In either of those cases, an attacker could construct a packet or packets that could be inserted into an SSH stream. To prevent this, implementers are encouraged to utilize commonly accepted MAC algorithms, and administrators are encouraged to watch current literature and discussions of cryptography to ensure that they are not using a MAC algorithm that has a recently found vulnerability or weakness. In summary, the use of this protocol without a reliable association of the binding between a host and its host keys is inherently insecure and is NOT RECOMMENDED. However, it may be necessary in non-security-critical environments, and will still provide protection against passive attacks. Implementers of protocols and applications running on top of this protocol should keep this possibility in mind. 9.3.5. Denial of Service This protocol is designed to be used over a reliable transport. If transmission errors or message manipulation occur, the connection is closed. The connection SHOULD be re-established if this occurs. Denial of service attacks of this type (wire cutter) are almost impossible to avoid. In addition, this protocol is vulnerable to denial of service attacks because an attacker can force the server to go through the CPU and memory intensive tasks of connection setup and key exchange without authenticating. Implementers SHOULD provide features that make this Ylonen & Lonvick Standards Track [Page 19] RFC 4251 SSH Protocol Architecture January 2006 more difficult, for example, only allowing connections from a subset of clients known to have valid users. 9.3.6. Covert Channels The protocol was not designed to eliminate covert channels. For example, the padding, SSH_MSG_IGNORE messages, and several other places in the protocol can be used to pass covert information, and the recipient has no reliable way of verifying whether such information is being sent. 9.3.7. Forward Secrecy It should be noted that the Diffie-Hellman key exchanges may provide perfect forward secrecy (PFS). PFS is essentially defined as the cryptographic property of a key-establishment protocol in which the compromise of a session key or long-term private key after a given session does not cause the compromise of any earlier session [ANSI-T1.523-2001]. SSH sessions resulting from a key exchange using the diffie-hellman methods described in the section Diffie-Hellman Key Exchange of [SSH-TRANS] (including "diffie-hellman-group1-sha1" and "diffie-hellman-group14-sha1") are secure even if private keying/authentication material is later revealed, but not if the session keys are revealed. So, given this definition of PFS, SSH does have PFS. However, this property is not commuted to any of the applications or protocols using SSH as a transport. The transport layer of SSH provides confidentiality for password authentication and other methods that rely on secret data. Of course, if the DH private parameters for the client and server are revealed, then the session key is revealed, but these items can be thrown away after the key exchange completes. It's worth pointing out that these items should not be allowed to end up on swap space and that they should be erased from memory as soon as the key exchange completes. 9.3.8. Ordering of Key Exchange Methods As stated in the section on Algorithm Negotiation of [SSH-TRANS], each device will send a list of preferred methods for key exchange. The most-preferred method is the first in the list. It is RECOMMENDED that the algorithms be sorted by cryptographic strength, strongest first. Some additional guidance for this is given in [RFC3766]. Ylonen & Lonvick Standards Track [Page 20] RFC 4251 SSH Protocol Architecture January 2006 9.3.9. Traffic Analysis Passive monitoring of any protocol may give an attacker some information about the session, the user, or protocol specific information that they would otherwise not be able to garner. For example, it has been shown that traffic analysis of an SSH session can yield information about the length of the password - [Openwall] and [USENIX]. Implementers should use the SSH_MSG_IGNORE packet, along with the inclusion of random lengths of padding, to thwart attempts at traffic analysis. Other methods may also be found and implemented. 9.4. Authentication Protocol The purpose of this protocol is to perform client user authentication. It assumes that this runs over a secure transport layer protocol, which has already authenticated the server machine, established an encrypted communications channel, and computed a unique session identifier for this session. Several authentication methods with different security characteristics are allowed. It is up to the server's local policy to decide which methods (or combinations of methods) it is willing to accept for each user. Authentication is no stronger than the weakest combination allowed. The server may go into a sleep period after repeated unsuccessful authentication attempts to make key search more difficult for attackers. Care should be taken so that this doesn't become a self- denial of service vector. 9.4.1. Weak Transport If the transport layer does not provide confidentiality, authentication methods that rely on secret data SHOULD be disabled. If it does not provide strong integrity protection, requests to change authentication data (e.g., a password change) SHOULD be disabled to prevent an attacker from modifying the ciphertext without being noticed, or rendering the new authentication data unusable (denial of service). The assumption stated above, that the Authentication Protocol only runs over a secure transport that has previously authenticated the server, is very important to note. People deploying SSH are reminded of the consequences of man-in-the-middle attacks if the client does not have a very strong a priori association of the server with the host key of that server. Specifically, for the case of the Authentication Protocol, the client may form a session to a man-in- Ylonen & Lonvick Standards Track [Page 21] RFC 4251 SSH Protocol Architecture January 2006 the-middle attack device and divulge user credentials such as their username and password. Even in the cases of authentication where no user credentials are divulged, an attacker may still gain information they shouldn't have by capturing key-strokes in much the same way that a honeypot works. 9.4.2. Debug Messages Special care should be taken when designing debug messages. These messages may reveal surprising amounts of information about the host if not properly designed. Debug messages can be disabled (during user authentication phase) if high security is required. Administrators of host machines should make all attempts to compartmentalize all event notification messages and protect them from unwarranted observation. Developers should be aware of the sensitive nature of some of the normal event and debug messages, and may want to provide guidance to administrators on ways to keep this information away from unauthorized people. Developers should consider minimizing the amount of sensitive information obtainable by users during the authentication phase, in accordance with the local policies. For this reason, it is RECOMMENDED that debug messages be initially disabled at the time of deployment and require an active decision by an administrator to allow them to be enabled. It is also RECOMMENDED that a message expressing this concern be presented to the administrator of a system when the action is taken to enable debugging messages. 9.4.3. Local Security Policy The implementer MUST ensure that the credentials provided validate the professed user and also MUST ensure that the local policy of the server permits the user the access requested. In particular, because of the flexible nature of the SSH connection protocol, it may not be possible to determine the local security policy, if any, that should apply at the time of authentication because the kind of service being requested is not clear at that instant. For example, local policy might allow a user to access files on the server, but not start an interactive shell. However, during the authentication protocol, it is not known whether the user will be accessing files, attempting to use an interactive shell, or even both. In any event, where local security policy for the server host exists, it MUST be applied and enforced correctly. Implementers are encouraged to provide a default local policy and make its parameters known to administrators and users. At the discretion of the implementers, this default policy may be along the lines of anything-goes where there are no restrictions placed upon users, or it may be along the lines of excessively-restrictive, in Ylonen & Lonvick Standards Track [Page 22] RFC 4251 SSH Protocol Architecture January 2006 which case, the administrators will have to actively make changes to the initial default parameters to meet their needs. Alternatively, it may be some attempt at providing something practical and immediately useful to the administrators of the system so they don't have to put in much effort to get SSH working. Whatever choice is made must be applied and enforced as required above. 9.4.4 Public Key Authentication The use of public key authentication assumes that the client host has not been compromised. It also assumes that the private key of the server host has not been compromised. This risk can be mitigated by the use of passphrases on private keys; however, this is not an enforceable policy. The use of smartcards, or other technology to make passphrases an enforceable policy is suggested. The server could require both password and public key authentication; however, this requires the client to expose its password to the server (see the section on Password Authentication below.) 9.4.5. Password Authentication The password mechanism, as specified in the authentication protocol, assumes that the server has not been compromised. If the server has been compromised, using password authentication will reveal a valid username/password combination to the attacker, which may lead to further compromises. This vulnerability can be mitigated by using an alternative form of authentication. For example, public key authentication makes no assumptions about security on the server. 9.4.6. Host-Based Authentication Host-based authentication assumes that the client has not been compromised. There are no mitigating strategies, other than to use host-based authentication in combination with another authentication method. Ylonen & Lonvick Standards Track [Page 23] RFC 4251 SSH Protocol Architecture January 2006 9.5. Connection Protocol 9.5.1. End Point Security End point security is assumed by the connection protocol. If the server has been compromised, any terminal sessions, port forwarding, or systems accessed on the host are compromised. There are no mitigating factors for this. If the client has been compromised, and the server fails to stop the attacker at the authentication protocol, all services exposed (either as subsystems or through forwarding) will be vulnerable to attack. Implementers SHOULD provide mechanisms for administrators to control which services are exposed to limit the vulnerability of other services. These controls might include controlling which machines and ports can be targeted in port-forwarding operations, which users are allowed to use interactive shell facilities, or which users are allowed to use exposed subsystems. 9.5.2. Proxy Forwarding The SSH connection protocol allows for proxy forwarding of other protocols such as SMTP, POP3, and HTTP. This may be a concern for network administrators who wish to control the access of certain applications by users located outside of their physical location. Essentially, the forwarding of these protocols may violate site- specific security policies, as they may be undetectably tunneled through a firewall. Implementers SHOULD provide an administrative mechanism to control the proxy forwarding functionality so that site-specific security policies may be upheld. In addition, a reverse proxy forwarding functionality is available, which, again, can be used to bypass firewall controls. As indicated above, end-point security is assumed during proxy forwarding operations. Failure of end-point security will compromise all data passed over proxy forwarding. 9.5.3. X11 Forwarding Another form of proxy forwarding provided by the SSH connection protocol is the forwarding of the X11 protocol. If end-point security has been compromised, X11 forwarding may allow attacks against the X11 server. Users and administrators should, as a matter of course, use appropriate X11 security mechanisms to prevent unauthorized use of the X11 server. Implementers, administrators, and users who wish to further explore the security mechanisms of X11 are invited to read [SCHEIFLER] and analyze previously reported Ylonen & Lonvick Standards Track [Page 24] RFC 4251 SSH Protocol Architecture January 2006 problems with the interactions between SSH forwarding and X11 in CERT vulnerabilities VU#363181 and VU#118892 [CERT]. X11 display forwarding with SSH, by itself, is not sufficient to correct well known problems with X11 security [VENEMA]. However, X11 display forwarding in SSH (or other secure protocols), combined with actual and pseudo-displays that accept connections only over local IPC mechanisms authorized by permissions or access control lists (ACLs), does correct many X11 security problems, as long as the "none" MAC is not used. It is RECOMMENDED that X11 display implementations default to allow the display to open only over local IPC. It is RECOMMENDED that SSH server implementations that support X11 forwarding default to allow the display to open only over local IPC. On single-user systems, it might be reasonable to default to allow the local display to open over TCP/IP. Implementers of the X11 forwarding protocol SHOULD implement the magic cookie access-checking spoofing mechanism, as described in [SSH-CONNECT], as an additional mechanism to prevent unauthorized use of the proxy. Ylonen & Lonvick Standards Track [Page 25] RFC 4251 SSH Protocol Architecture January 2006 10. References 10.1. Normative References [SSH-TRANS] Ylonen, T. and C. Lonvick, Ed., "The Secure Shell (SSH) Transport Layer Protocol", RFC 4253, January 2006. [SSH-USERAUTH] Ylonen, T. and C. Lonvick, Ed., "The Secure Shell (SSH) Authentication Protocol", RFC 4252, January 2006. [SSH-CONNECT] Ylonen, T. and C. Lonvick, Ed., "The Secure Shell (SSH) Connection Protocol", RFC 4254, January 2006. [SSH-NUMBERS] Lehtinen, S. and C. Lonvick, Ed., "The Secure Shell (SSH) Protocol Assigned Numbers", RFC 4250, January 2006. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 2434, October 1998. [RFC3066] Alvestrand, H., "Tags for the Identification of Languages", BCP 47, RFC 3066, January 2001. [RFC3629] Yergeau, F., "UTF-8, a transformation format of ISO 10646", STD 63, RFC 3629, November 2003. 10.2. Informative References [RFC0822] Crocker, D., "Standard for the format of ARPA Internet text messages", STD 11, RFC 822, August 1982. [RFC0854] Postel, J. and J. Reynolds, "Telnet Protocol Specification", STD 8, RFC 854, May 1983. [RFC1034] Mockapetris, P., "Domain names - concepts and facilities", STD 13, RFC 1034, November 1987. Ylonen & Lonvick Standards Track [Page 26] RFC 4251 SSH Protocol Architecture January 2006 [RFC1282] Kantor, B., "BSD Rlogin", RFC 1282, December 1991. [RFC4120] Neuman, C., Yu, T., Hartman, S., and K. Raeburn, "The Kerberos Network Authentication Service (V5)", RFC 4120, July 2005. [RFC1964] Linn, J., "The Kerberos Version 5 GSS-API Mechanism", RFC 1964, June 1996. [RFC2025] Adams, C., "The Simple Public-Key GSS-API Mechanism (SPKM)", RFC 2025, October 1996. [RFC2085] Oehler, M. and R. Glenn, "HMAC-MD5 IP Authentication with Replay Prevention", RFC 2085, February 1997. [RFC2104] Krawczyk, H., Bellare, M., and R. Canetti, "HMAC: Keyed-Hashing for Message Authentication", RFC 2104, February 1997. [RFC2246] Dierks, T. and C. Allen, "The TLS Protocol Version 1.0", RFC 2246, January 1999. [RFC2410] Glenn, R. and S. Kent, "The NULL Encryption Algorithm and Its Use With IPsec", RFC 2410, November 1998. [RFC2743] Linn, J., "Generic Security Service Application Program Interface Version 2, Update 1", RFC 2743, January 2000. [RFC3766] Orman, H. and P. Hoffman, "Determining Strengths For Public Keys Used For Exchanging Symmetric Keys", BCP 86, RFC 3766, April 2004. [RFC4086] Eastlake, D., 3rd, Schiller, J., and S. Crocker, "Randomness Requirements for Security", BCP 106, RFC 4086, June 2005. [FIPS-180-2] US National Institute of Standards and Technology, "Secure Hash Standard (SHS)", Federal Information Processing Standards Publication 180-2, August 2002. [FIPS-186-2] US National Institute of Standards and Technology, "Digital Signature Standard (DSS)", Federal Information Processing Standards Publication 186- 2, January 2000. Ylonen & Lonvick Standards Track [Page 27] RFC 4251 SSH Protocol Architecture January 2006 [FIPS-197] US National Institute of Standards and Technology, "Advanced Encryption Standard (AES)", Federal Information Processing Standards Publication 197, November 2001. [ANSI-T1.523-2001] American National Standards Institute, Inc., "Telecom Glossary 2000", ANSI T1.523-2001, February 2001. [SCHNEIER] Schneier, B., "Applied Cryptography Second Edition: protocols algorithms and source in code in C", John Wiley and Sons, New York, NY, 1996. [SCHEIFLER] Scheifler, R., "X Window System : The Complete Reference to Xlib, X Protocol, Icccm, Xlfd, 3rd edition.", Digital Press, ISBN 1555580882, February 1992. [KAUFMAN] Kaufman, C., Perlman, R., and M. Speciner, "Network Security: PRIVATE Communication in a PUBLIC World", Prentice Hall Publisher, 1995. [CERT] CERT Coordination Center, The., "http://www.cert.org/nav/index_red.html". [VENEMA] Venema, W., "Murphy's Law and Computer Security", Proceedings of 6th USENIX Security Symposium, San Jose CA http://www.usenix.org/publications/library/ proceedings/sec96/venema.html, July 1996. [ROGAWAY] Rogaway, P., "Problems with Proposed IP Cryptography", Unpublished paper http://www.cs.ucdavis.edu/~rogaway/ papers/draft- rogaway-ipsec-comments-00.txt, 1996. [DAI] Dai, W., "An attack against SSH2 protocol", Email to the SECSH Working Group ietf-ssh@netbsd.org ftp:// ftp.ietf.org/ietf-mail-archive/secsh/2002- 02.mail, Feb 2002. [BELLARE] Bellaire, M., Kohno, T., and C. Namprempre, "Authenticated Encryption in SSH: Fixing the SSH Binary Packet Protocol", Proceedings of the 9th ACM Conference on Computer and Communications Security, Sept 2002. Ylonen & Lonvick Standards Track [Page 28] RFC 4251 SSH Protocol Architecture January 2006 [Openwall] Solar Designer and D. Song, "SSH Traffic Analysis Attacks", Presentation given at HAL2001 and NordU2002 Conferences, Sept 2001. [USENIX] Song, X.D., Wagner, D., and X. Tian, "Timing Analysis of Keystrokes and SSH Timing Attacks", Paper given at 10th USENIX Security Symposium, 2001. Authors' Addresses Tatu Ylonen SSH Communications Security Corp Valimotie 17 00380 Helsinki Finland EMail: ylo@ssh.com Chris Lonvick (editor) Cisco Systems, Inc. 12515 Research Blvd. Austin 78759 USA EMail: clonvick@cisco.com Trademark Notice "ssh" is a registered trademark in the United States and/or other countries. Ylonen & Lonvick Standards Track [Page 29] RFC 4251 SSH Protocol Architecture January 2006 Full Copyright Statement Copyright (C) The Internet Society (2006). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgement Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Ylonen & Lonvick Standards Track [Page 30]